KERALA PSC CIVIL ENGINEERING MOCK TEST 8

KERALA PSC CIVIL ENGINEERING TECHNICAL EXAM MOCK TEST


Here you will find all the practice tests to improve your skills and speed and grasp the knowledge you need for exams. Take the online tests, get evaluated and improve your scores by attempting more and more questions. Mock tests will be uploaded daily. Try to score above  90 % for all mock tests to on top of all the upcoming civil engineering competitive exams .

  • Attend the quiz below 
  • 1 mark per question 
  • no negative marking 
  • correct answers and your score will be available after the submission of quiz
  • Correct answers wont be shown for unmarked questions. make sure to attend all the questions
  • after submitting the responses get back to the top of the page to view the score 

Comments

Post a Comment

Popular posts from this blog

UNITS OF MEASUREMENTS, PAINTING COEFFICIENT, OUT TURN, QUANTITY CALCULATION

Image
  DEDUCTION  • MASONRY : < 0.1 m2 - no deduction  • PLASTERING :  < 0.5 m2 - no deduction  0.5 - 3 m2 - one side deduction  > 3 - both side deduction  • End of beams, rafters, purlins < 0.05 m2 - no deduction  • Bearing of floors, roof slabs etc. - no deduction DIGREE OF ACCURACY  • Volume - 0.01 m3  • Area - 0.01 m2  • Dimension - 0.01 m  • Weight - 1kg  QUANTITY CALCULATION  PCC  • Maximum size of aggregate 40 mm  • For 1 m3 PCC - 0.95 m3 coarse aggregate is required  RCC  • Maximum size of aggregate 20 mm  • For 1m3 RCC - 0.90 m3 coarse aggregate is require  RCC For 1:1.5:3  Wt of cement = (1/3) x 0.90 x 1440 = 432 kg  Wt of sand = (1.5/3) x 0.90 x 1600 = 747 kg  PCC For 1:4:8  Wt of cement = (1/8) x 0.95 x 1440 = 171 kg  Wt of sand = (4/8) x 0.95 x 1660 = 760 kg PLASTERING  1:3 - 0.14 m3 / 10 m2 (sand) cement = (1/3) x 0.14 x 1440 = 67 kg  1:4 - 0.15 m3 / 10 m2 (sand) cement = (1/4) x 0.15 x 1440 = 54 kg  1:5 - 0.15 m3 / 10 m2 (sand) cement = (1/5) x 0.15 x 1440 = 43 kg
Read more

MACHINE TOOLS - SHAPER MACHINE

Image
The shaper is a machine tool used primarily for:  1. Producing a flat or plane surface which may be in a horizontal, a vertical or an angular plane.  2. Making slots, grooves and keyways  3. Producing contour of concave/convex or a combination of these Working Principle: The job is rigidly fixed on the machine table. The single point cutting tool held properly in the tool post is mounted on a reciprocating ram. The reciprocating motion of the ram is obtained by a quick return motion mechanism. As the ram reciprocates, the tool cuts the material during its forward stroke. During return, there is no cutting action and this stroke is called the idle stroke. The forward and return strokes constitute one operating cycle of the shaper.  Construction: The main parts of the Shaper machine is Base, Body (Pillar, Frame, Column), Cross rail, Ram and tool head (Tool Post, Tool Slide, Clamper Box Block). Base:  - The base is a heavy cast iron casting which is fixed to the shop floor.  - It supports
Read more

OPEN QUIZ RANKLIST 3

 1 56 / 63 HaRitHa 2 54 / 63 Sebin 3 53 / 63 Anuja sundareshan 4 53 / 63 Arun aravind 5 52 / 63 Faiz 6 51 / 63 aparna B 7 51 / 63 Veni 8 51 / 63 Anaswarakp 9 51 / 63 Akshay k 10 51 / 63 Minnu 11 50 / 63 Zehmat 12 50 / 63 Hima 13 49 / 63 Sreejith tk 14 48 / 63 AISHU 15 47 / 63 Prasee 16 47 / 63 Aswaniraj 17 46 / 63 Mumtaz 18 46 / 63 Ganga 19 45 / 63 Hannath N M 20 45 / 63 Arya... 21 44 / 63 Greesh 22 44 / 63 ANU M 23 43 / 63 Archana 24 43 / 63 Nirosha 25 43 / 63 CG 26 43 / 63 Nisham 27 43 / 63 Nikhil Murali 28 43 / 63 Suneesh 29 43 / 63 Aswathy 30 43 / 63 remya basanth 31 42 / 63 Haritha 32 41 / 63 Mohamed Hafeez 33 41 / 63 Aswati 34 41 / 63 salma  35 41 / 63 Akhila Ag 36 40 / 63 Gp 37 40 / 63 Aleena 38 40 / 63 Aami 39 40 / 63 Vrindha  40 39 / 63 Aiswaryasajeevan  41 38 / 63 Spread a smile 42 38 / 63 ashlin stanly 43 38
Read more